3db's Main System located in the basement

[3dbinCanada]

I always wanted seperates for a stereo system only because I think its kinda cool. I scored the following for a $525 Cdn . All it took was a 6 hour round trip and gas to get them. It was demonstrated by the seller and it all works. All Yamaha: power amp is a MX-600U, pre-amp is a CX-600U, and tuner is TX-530

These are not the pics of the actual units as I'm just getting around to setting it up

 

[3dbinCanada]

I'm adding a separates stack dedicated to 2 channel use only not because I think it will sound better than my AVR but because Ive always wanted one. I'm a die hard Yamaha guy and my stack is what else Yamaha. I'm not sure aesthetically which placement of the stack I want yet. What do you guys think? Option 1 or Option 2

Option 1

Option 2

 

[JStewart]

I think I prefer option 2 by a slight margin. Did you consider putting your turntable on top? Option 1 may look better if you did.
Nice score on the separates!

 

[3dbinCanada]

I think I prefer option 2 by a slight margin. Did you consider putting your turntable on top? Option 1 may look better if you did.
Nice score on the separates!

I'm definitely moving the turntable to the audio rack but I'm waiting for an Amazon order to come in for pads that I can put underneath the rack so I can move it more readily across the carpeted floor once the rack is loaded with gear.

 

[3dbinCanada]

I think I prefer option 2 by a slight margin. Did you consider putting your turntable on top? Option 1 may look better if you did.
Nice score on the separates!

Thanks J.

 

[3dbinCanada]

Deleting post because I posted in the wrong area.

 

[3dbinCanada]

Yesterday's cassettes

View attachment 67336 View attachment 67337 View attachment 67338 View attachment 67339 View attachment 67340 View attachment 67341 View attachment 67342 View attachment 67343

 

[3dbinCanada]

I moved things around in the room again and also wired up the amp selector switch so that both the power amp and the AVR can drive the towers.

 

[3dbinCanada]

The Yamaha EQ-550 arrived today very well packaged. I cleaned it up and put it in the stack. I think I goofed ordering this rack as I still want to fit in a Yamaha KX-1200 and Yamaha CD player but I don't think I have the shelf space. Its like playing audio rack tetras!! I will try different combos like putting the power amp in the middle rack and using the bottom rock to hold the deck, CD player, and preamp. If that doesn't work, I'll just remove the tuner out of the equation as I very seldom listen to radio, Besides, I have an AVR with a tuner as well.''

 

[3dbinCanada]

Here are the room curves all of which use 1/12 smoothing.

The individual subs responses plus the combination of both before using REW to produce the Harmon curve.

The blue trace below is the same trace as the green trace in the previous graph, before EQ. The green trace below is the EQ'd bass response.

Below is the full frequency sweep in room response for the movie configuration. The red trace is the AVR with PEQ set to FLAT . The blue trace has PEQ turned off.

don't use the AVR's PEQ function with music. I still use the AVR's bass management in the brown trace where both sub and the towers get bass. The green trace is when the AVR is set to Pure Direct which turns off the bass management and its only the towers producing the full frequency sweep.

 

[JStewart]

The green trace is when the AVR is set to Pure Direct

Great low end full range extension on those mains.

The blue trace below is the same trace as the green trace in the previous graph, before EQ. The green trace below is the EQ'd bass response.

So, does the EQ’d response sound much better to you? The raw response is pretty good to begin with.

 

[3dbinCanada]

Great low end full range extension on those mains.

So, does the EQ’d response sound much better to you? The raw response is pretty good to begin with.

I haven't had a chance to use it. Will keep you posted.

 

[3dbinCanada]

I haven't had a chance to use it. Will keep you posted.

It sound good but guess what?? I moved sh?t around again because I wanted to increase the distance between the mains and pull them further out. I got an additional 10" between them and additional 6" away from the wall behind them. I also got my separates stack up and running.

 

[JStewart]

Very good

 

[3dbinCanada]

Here are the measurements from the last room change. What I did was post the measurements comparing the current (new) room setup compared to the previous (last) room setup.

 

[3dbinCanada]

I purchased my 3rd Yamaha KX-1200 deck and it came in yesterday. wow it looks brand new, easily the best looking out of the three. I got the deck connected up to the stack finally. It still wasn't working the way I wanted it too after 3 different connect configurations. I decided at this point to stop and read the owners manual of the preamp. I banged my head on the desk repeatedly when I saw the "record selector switch" in the manual. I was tired at this point and went to bed. I tried the connecting thing again and bingo!! I also bypassed the tape monitor loop on the EQ as I want to record my source material unaltered by the EQ.

I also put in the calibration tape and the spectrum analyzer pegged the tape output at 3KHz which is the frequency that was recorded on the tape.

 

[3dbinCanada]

I didn't like the sub stuck out in the room like that so I moved it back to a previous location tucked in the corner which is on the left side if the sofa and aimed down the length of the sofa.

Here are the responses. I compared new to previous (old) location

 

[3dbinCanada]

My CD rack came in from Amazon.