Mismatched SUB help needed

ciotime

New Member
Thread Starter
Joined
Nov 25, 2020
Messages
23
More  
Preamp, Processor or Receiver
Denon X3700H
Main Amp
Denon X3700H
Additional Amp
Denon AVR 3313
Universal / Blu-ray / CD Player
Sony
Front Speakers
B&W 602 S3
Surround Back Speakers
B&W 303
Subwoofers
Paradigm PDR12 and PDR10
Video Display Device
BenQ HT3550
Screen
Grandview Tab Tension
Hi...a noob here needing some help. I currently have 2 subs ( Paradigm PDR10 and PDR12 ) in a dedicated HT room ( 13x19x8 ) that is functional but quite old. I'm planning on getting the SVS PB-1000 since my old subs can't really go down to the lower frequencies.
1) Will I be better off using 2 SVS PB-1000 rather than integrating the SVS to the existing 2 Paradigm subs? I would rather integrate them than having to spend for another sub.
2) Should I just use the PDR12 and SVS PB-1000 for a dual setup or is a 3 sub setup doable?
3) I understand that Audyssey will only EQ to the capability of the less capable Paradigm Subwoofers but can I use the miniDSP to get around this problem and be able to maximize the SVS's potential? If so how do I go about doing this? A step by step guide would be truly helpful...thanks.

*PDR-10

Amplifier: 120 watts RMS / 360 watts Peak
Subwoofer Cutoff Frequency: Variable 50 Hz – 150 Hz
Bass Driver: 254-mm (10 in) carbon-fiber-reinforced composite cone, 38-mm (1-1/2 in) voice coil
Low Frequency Extension: 27 Hz (DIN)


*PDR-12

Amplifier: 150 watts RMS / 450 watts Peak
Low Pass Filter Frequency: Variable 50Hz-150Hz
Low Frequency Driver: 305-mm ( 12" ) carbon-fiber-reinforced composite cone, 51-mm (2 in) voice coil
Low Frequency Extension: 24 Hz (DIN)



*SVS PB-1000 Specs
Amplifier Power Rating300 W RMS
720 W Peak
Drivers10" / 25.4 cm
Frequency Response19 to 270 Hz
Amplifier ClassClass-D
 

Wayne A. Pflughaupt

Moderator
Staff member
Joined
May 21, 2017
Messages
633
Location
Corpus Christi, TX
More  
Preamp, Processor or Receiver
Yamaha CX-A5000 A/V Preamp / Processor
Main Amp
Yamaha RX-Z9 AV Receiver (as multichannel amp)
Universal / Blu-ray / CD Player
Denon DCT-3313 UDCI Universal Disc Player
Front Speakers
Canton Karat 920
Center Channel Speaker
Canton Karat 920
Front Wide Speakers
Realistic Minimus 7 (front EFX speakers)
Surround Speakers
Canton Plus D
Surround Back Speakers
Yamaha YDP2006 Digital Parametric EQ (front mains)
Front Height Speakers
Yamaha YDP2006 Digital Parametric EQ (surrounds)
Rear Height Speakers
Yamaha YDP2006 Digital Parametric EQ (sub)
Subwoofers
Hsu ULS-15 MKII
Other Speakers or Equipment
Adcom ACE-515 (for power management)
Video Display Device
Yamaha DT-2 (digital clock display)
Screen
Pioneer PDP-6010FD 60" Plasma TV
Remote Control
Stock Yamaha Remote
Streaming Equipment
Roku Express
Other Equipment
Audio Control R130 Real Time Analyzer
Mixing subs of different capabilities can be problematic, as you can see in this old post with graphs.

EQ for the Paradigms can help, but that means they will run out of headroom in a hurry trying to get down as low as the SVS. Plus in my experience trying to EQ a sub to enhance its extension, it never sounds as good as a sub that just “gets it” naturally.

Largely, your success at integrating the three will depend on your headroom. If you are “over-sub’d”, meaning you have more subs than the room needs and they are basically “loafing,” they it can work. But if your situation has the Paradigms working hard, then I doubt this will turn out well.

Regards,
Wayne
 

Todd Anderson

Editor / Senior Admin
Staff member
Joined
Jan 20, 2017
Messages
9,138
Location
Balt/Wash Metro
More  
Preamp, Processor or Receiver
StormAudio ISP.24 MK2
Main Amp
Emotiva XPA-5
Additional Amp
Emotiva XPA Gen3 2.8 multichannel amp
Other Amp
Denon X8500H
Computer Audio
AudioEngine A2+
DAC
THX ONYX
Universal / Blu-ray / CD Player
Kaleidescape TERRA, OPPO UDP-203, Panasonic UB9000
Front Speakers
GoldenEar Technology Triton One.R
Center Channel Speaker
GoldenEar Technology SuperCenter Reference
Surround Speakers
SVS Ultra Surround
Surround Back Speakers
SVS Ultra Bookshelf
Front Height Speakers
SVS Prime Elevation x4 (Top Front, Top Mid-Front)
Rear Height Speakers
SVS Prime Elevation x4 (Top Middle, Top Rear)
Subwoofers
dual SVS SB16s + dual PSA XS30s
Other Speakers or Equipment
Behringer 1124p; Aura Bass Shaker Pros; SuperSub X
Video Display Device
JVC NX7
Screen
Seymour Screen Excellence, Enlightor NEO AT Screen
Streaming Equipment
iFi Audio Zen Blue
Streaming Subscriptions
Qobuz, TIDAL, Spotify, ROON
Other Equipment
LG Electronics 65-inch B6 OLED, Sony 65-inch X900F, ZeroSurge 8R15W x 2, ZeroSurge 2R15W x 2
Agree with Wayne. Your PDR10 is likely going to weigh down your experience, especially as you reach reference levels. If it's in the budget, I'd sell the Paradigms and go dual SVS.
 

ciotime

New Member
Thread Starter
Joined
Nov 25, 2020
Messages
23
More  
Preamp, Processor or Receiver
Denon X3700H
Main Amp
Denon X3700H
Additional Amp
Denon AVR 3313
Universal / Blu-ray / CD Player
Sony
Front Speakers
B&W 602 S3
Surround Back Speakers
B&W 303
Subwoofers
Paradigm PDR12 and PDR10
Video Display Device
BenQ HT3550
Screen
Grandview Tab Tension
So even using the miniDSP won't help?
 

Sonnie

Senior Admin
Staff member
Joined
Apr 2, 2017
Messages
5,055
Location
Alabama
More  
Preamp, Processor or Receiver
StormAudio ISP Elite 24 MK3 Processor
Main Amp
McIntosh MC1.25KW Monoblock Amps
Additional Amp
StormAudio PA 16 MK3
Computer Audio
Intel NUC w/ Roon ROCK
Universal / Blu-ray / CD Player
Panasonic UB9000 4K UHD Player (for media discs)
Front Speakers
RTJ 410
Center Channel Speaker
MartinLogan Focus C-18
Front Wide Speakers
JTR Neosis 110HT
Surround Speakers
JTR Neosis 210RT
Surround Back Speakers
JTR Neosis 210RT
Front Height Speakers
JTR Neosis 110HT-SL
Rear Height Speakers
JTR Neosis 110HT-SL
Subwoofers
JTR Captivator 2400 x6
Other Speakers or Equipment
VTI Amp Stands for the Monoblocks
Video Display Device
Sony 98X90L
Remote Control
Universal MX-890
Streaming Equipment
FireCube for movies and Lenova Carbon X1 for Roon
Streaming Subscriptions
Lifetime Roon Subscription
Tidal
qobuz
Netflix
Amazon Prime
Satellite System
Dish Joey 4K
Other Equipment
Zero Surge 8R15W-1 | Salamander Synergy Equipment Stand
About the only thing the miniDSP will do is help you get the subs time aligned... and you could go ahead and use PEQ filters to tame the high peaks before running Audyssey. This would help in the level settings between the subs and mains.

You won't have any issues until one sub starts to outrun the other. You can level match your subs to 70dB and then measure each sub and gradually increase the volume and repeat measurements. Eventually you will see one sub start to lower in measurement response than the other, and that would be the level at which the subs are no longer on the same page.

You can also let Audyssey do it's thing, then measure only the subs combined. At lower levels the response will look good, as you increase the volume and continue to measure, if one sub is outrunning the other, the response will start to reshape. If you can get the volume as loud as you will ever use it and the response continues to be smooth or not reshape too much, you may be fine.

Measurements are key to know what you are dealing with.
 

Todd Anderson

Editor / Senior Admin
Staff member
Joined
Jan 20, 2017
Messages
9,138
Location
Balt/Wash Metro
More  
Preamp, Processor or Receiver
StormAudio ISP.24 MK2
Main Amp
Emotiva XPA-5
Additional Amp
Emotiva XPA Gen3 2.8 multichannel amp
Other Amp
Denon X8500H
Computer Audio
AudioEngine A2+
DAC
THX ONYX
Universal / Blu-ray / CD Player
Kaleidescape TERRA, OPPO UDP-203, Panasonic UB9000
Front Speakers
GoldenEar Technology Triton One.R
Center Channel Speaker
GoldenEar Technology SuperCenter Reference
Surround Speakers
SVS Ultra Surround
Surround Back Speakers
SVS Ultra Bookshelf
Front Height Speakers
SVS Prime Elevation x4 (Top Front, Top Mid-Front)
Rear Height Speakers
SVS Prime Elevation x4 (Top Middle, Top Rear)
Subwoofers
dual SVS SB16s + dual PSA XS30s
Other Speakers or Equipment
Behringer 1124p; Aura Bass Shaker Pros; SuperSub X
Video Display Device
JVC NX7
Screen
Seymour Screen Excellence, Enlightor NEO AT Screen
Streaming Equipment
iFi Audio Zen Blue
Streaming Subscriptions
Qobuz, TIDAL, Spotify, ROON
Other Equipment
LG Electronics 65-inch B6 OLED, Sony 65-inch X900F, ZeroSurge 8R15W x 2, ZeroSurge 2R15W x 2
If you do integrate, I would lose the 10" paradigm and only run with the 12... try duals with that.
 

ciotime

New Member
Thread Starter
Joined
Nov 25, 2020
Messages
23
More  
Preamp, Processor or Receiver
Denon X3700H
Main Amp
Denon X3700H
Additional Amp
Denon AVR 3313
Universal / Blu-ray / CD Player
Sony
Front Speakers
B&W 602 S3
Surround Back Speakers
B&W 303
Subwoofers
Paradigm PDR12 and PDR10
Video Display Device
BenQ HT3550
Screen
Grandview Tab Tension
About the only thing the miniDSP will do is help you get the subs time aligned... and you could go ahead and use PEQ filters to tame the high peaks before running Audyssey. This would help in the level settings between the subs and mains.

You won't have any issues until one sub starts to outrun the other. You can level match your subs to 70dB and then measure each sub and gradually increase the volume and repeat measurements. Eventually you will see one sub start to lower in measurement response than the other, and that would be the level at which the subs are no longer on the same page.

You can also let Audyssey do it's thing, then measure only the subs combined. At lower levels the response will look good, as you increase the volume and continue to measure, if one sub is outrunning the other, the response will start to reshape. If you can get the volume as loud as you will ever use it and the response continues to be smooth or not reshape too much, you may be fine.

Measurements are key to know what you are dealing with.
Thank you so much for the help. Being a newbie lot's of word's you mentioned are very foreign to me but I'll try to make sense as much as I can. I do need some clarification is you don't mind.

1) You can level match your subs to 70dB-is this the same as gain match? So use an SPL meter and adjust the volume at the back of each sub until they're all at 70dB on the SPL meter?

2) You can also let Audyssey do it's thing, then measure only the subs combined-Measure using the REW software right?
 

ciotime

New Member
Thread Starter
Joined
Nov 25, 2020
Messages
23
More  
Preamp, Processor or Receiver
Denon X3700H
Main Amp
Denon X3700H
Additional Amp
Denon AVR 3313
Universal / Blu-ray / CD Player
Sony
Front Speakers
B&W 602 S3
Surround Back Speakers
B&W 303
Subwoofers
Paradigm PDR12 and PDR10
Video Display Device
BenQ HT3550
Screen
Grandview Tab Tension
If you do integrate, I would lose the 10" paradigm and only run with the 12... try duals with that.
Thanks...most likely this is what will happen but I'll try to intergrade the 10" and just see what happens.
 

Sonnie

Senior Admin
Staff member
Joined
Apr 2, 2017
Messages
5,055
Location
Alabama
More  
Preamp, Processor or Receiver
StormAudio ISP Elite 24 MK3 Processor
Main Amp
McIntosh MC1.25KW Monoblock Amps
Additional Amp
StormAudio PA 16 MK3
Computer Audio
Intel NUC w/ Roon ROCK
Universal / Blu-ray / CD Player
Panasonic UB9000 4K UHD Player (for media discs)
Front Speakers
RTJ 410
Center Channel Speaker
MartinLogan Focus C-18
Front Wide Speakers
JTR Neosis 110HT
Surround Speakers
JTR Neosis 210RT
Surround Back Speakers
JTR Neosis 210RT
Front Height Speakers
JTR Neosis 110HT-SL
Rear Height Speakers
JTR Neosis 110HT-SL
Subwoofers
JTR Captivator 2400 x6
Other Speakers or Equipment
VTI Amp Stands for the Monoblocks
Video Display Device
Sony 98X90L
Remote Control
Universal MX-890
Streaming Equipment
FireCube for movies and Lenova Carbon X1 for Roon
Streaming Subscriptions
Lifetime Roon Subscription
Tidal
qobuz
Netflix
Amazon Prime
Satellite System
Dish Joey 4K
Other Equipment
Zero Surge 8R15W-1 | Salamander Synergy Equipment Stand
Thank you so much for the help. Being a newbie lot's of word's you mentioned are very foreign to me but I'll try to make sense as much as I can. I do need some clarification is you don't mind.

1) You can level match your subs to 70dB-is this the same as gain match? So use an SPL meter and adjust the volume at the back of each sub until they're all at 70dB on the SPL meter?

2) You can also let Audyssey do it's thing, then measure only the subs combined-Measure using the REW software right?
1) You can level match this way yes... or use REW's built-in SPL meter... or measure each sub and adjust the volume until the response measurements line up fairly well. I like measuring each sub better because you are seeing the entire frequency response, while an SPL meter only measures the highest frequency peak and may not really be representative of the subs being truly level matched... at least not until their respective frequency response is smoothed out.
2) Yes... using REW.
 

ciotime

New Member
Thread Starter
Joined
Nov 25, 2020
Messages
23
More  
Preamp, Processor or Receiver
Denon X3700H
Main Amp
Denon X3700H
Additional Amp
Denon AVR 3313
Universal / Blu-ray / CD Player
Sony
Front Speakers
B&W 602 S3
Surround Back Speakers
B&W 303
Subwoofers
Paradigm PDR12 and PDR10
Video Display Device
BenQ HT3550
Screen
Grandview Tab Tension
1) You can level match this way yes... or use REW's built-in SPL meter... or measure each sub and adjust the volume until the response measurements line up fairly well. I like measuring each sub better because you are seeing the entire frequency response, while an SPL meter only measures the highest frequency peak and may not really be representative of the subs being truly level matched... at least not until their respective frequency response is smoothed out.
2) Yes... using REW.
Thanks....so do you think using the miniDSP 2X4HD will help? If so at which step of the process do I use it? Before or after measuring? Do I do the tweaking like set delays cutoff etc at the miniDSP or at the AVR?
 

Sonnie

Senior Admin
Staff member
Joined
Apr 2, 2017
Messages
5,055
Location
Alabama
More  
Preamp, Processor or Receiver
StormAudio ISP Elite 24 MK3 Processor
Main Amp
McIntosh MC1.25KW Monoblock Amps
Additional Amp
StormAudio PA 16 MK3
Computer Audio
Intel NUC w/ Roon ROCK
Universal / Blu-ray / CD Player
Panasonic UB9000 4K UHD Player (for media discs)
Front Speakers
RTJ 410
Center Channel Speaker
MartinLogan Focus C-18
Front Wide Speakers
JTR Neosis 110HT
Surround Speakers
JTR Neosis 210RT
Surround Back Speakers
JTR Neosis 210RT
Front Height Speakers
JTR Neosis 110HT-SL
Rear Height Speakers
JTR Neosis 110HT-SL
Subwoofers
JTR Captivator 2400 x6
Other Speakers or Equipment
VTI Amp Stands for the Monoblocks
Video Display Device
Sony 98X90L
Remote Control
Universal MX-890
Streaming Equipment
FireCube for movies and Lenova Carbon X1 for Roon
Streaming Subscriptions
Lifetime Roon Subscription
Tidal
qobuz
Netflix
Amazon Prime
Satellite System
Dish Joey 4K
Other Equipment
Zero Surge 8R15W-1 | Salamander Synergy Equipment Stand
If you've already purchased it, you can use it to time align the speakers, but that might be quite the chore if you're not familiar with the process. Otherwise, I would start with the two larger subs assuming your Denon has the Sub EQ HT and can time align two of your subs. Run Audyssey with those two subs, then do some measurements as previously outlined.
 

ciotime

New Member
Thread Starter
Joined
Nov 25, 2020
Messages
23
More  
Preamp, Processor or Receiver
Denon X3700H
Main Amp
Denon X3700H
Additional Amp
Denon AVR 3313
Universal / Blu-ray / CD Player
Sony
Front Speakers
B&W 602 S3
Surround Back Speakers
B&W 303
Subwoofers
Paradigm PDR12 and PDR10
Video Display Device
BenQ HT3550
Screen
Grandview Tab Tension
I've posted here the REW results of the 3 subs routed to the miniDSP.
graph.jpg


2 subs on the front and 1 sub at the rear center. No EQ etc yet. Just the summation of the 3 subs turned on. Measurement was made from 10HZ to 120HZ. I don't really know what the graph says. I just know there's a dip at about the 38HZ and 75HZ region. Can anyone please check the results if it's not bad/average/bad? Thanks.
 

Sonnie

Senior Admin
Staff member
Joined
Apr 2, 2017
Messages
5,055
Location
Alabama
More  
Preamp, Processor or Receiver
StormAudio ISP Elite 24 MK3 Processor
Main Amp
McIntosh MC1.25KW Monoblock Amps
Additional Amp
StormAudio PA 16 MK3
Computer Audio
Intel NUC w/ Roon ROCK
Universal / Blu-ray / CD Player
Panasonic UB9000 4K UHD Player (for media discs)
Front Speakers
RTJ 410
Center Channel Speaker
MartinLogan Focus C-18
Front Wide Speakers
JTR Neosis 110HT
Surround Speakers
JTR Neosis 210RT
Surround Back Speakers
JTR Neosis 210RT
Front Height Speakers
JTR Neosis 110HT-SL
Rear Height Speakers
JTR Neosis 110HT-SL
Subwoofers
JTR Captivator 2400 x6
Other Speakers or Equipment
VTI Amp Stands for the Monoblocks
Video Display Device
Sony 98X90L
Remote Control
Universal MX-890
Streaming Equipment
FireCube for movies and Lenova Carbon X1 for Roon
Streaming Subscriptions
Lifetime Roon Subscription
Tidal
qobuz
Netflix
Amazon Prime
Satellite System
Dish Joey 4K
Other Equipment
Zero Surge 8R15W-1 | Salamander Synergy Equipment Stand
Looks pretty good if you bring that area from 20-30Hz down about 8-10dB. The miniDSP can help with this with use of PEQ filters. Then you can run Audyssey and it won't bring your sub levels down so much.
 

ciotime

New Member
Thread Starter
Joined
Nov 25, 2020
Messages
23
More  
Preamp, Processor or Receiver
Denon X3700H
Main Amp
Denon X3700H
Additional Amp
Denon AVR 3313
Universal / Blu-ray / CD Player
Sony
Front Speakers
B&W 602 S3
Surround Back Speakers
B&W 303
Subwoofers
Paradigm PDR12 and PDR10
Video Display Device
BenQ HT3550
Screen
Grandview Tab Tension
Looks pretty good if you bring that area from 20-30Hz down about 8-10dB. The miniDSP can help with this with use of PEQ filters. Then you can run Audyssey and it won't bring your sub levels down so much.
Thanks again Sonnie for the help...will try tinkering with the PEQ as per advised. FYI the SVS PB-1000 is at the front left and the PDR12 is at the front right. Rear center about 1 foot from the wall ( with 2" absorption panels ) is the PDR10.

Also should I also apply a HPF? Saw someone suggest it to protect the subs. Supposed to set it just below the tuning freq of the subs. Problem is I don't know the tuning freq of my subs. Is it the same as the Low Frequency Extension?
Should I set it at around 20HZ?
 
Last edited:

ciotime

New Member
Thread Starter
Joined
Nov 25, 2020
Messages
23
More  
Preamp, Processor or Receiver
Denon X3700H
Main Amp
Denon X3700H
Additional Amp
Denon AVR 3313
Universal / Blu-ray / CD Player
Sony
Front Speakers
B&W 602 S3
Surround Back Speakers
B&W 303
Subwoofers
Paradigm PDR12 and PDR10
Video Display Device
BenQ HT3550
Screen
Grandview Tab Tension
I did some tinkering on REW. After EQ this is what I got. Saw a video that instead of using a house curve in REW EQ to just instead flatten the response and to try to get it to hug the line as much as possible. I'm still a noob so I can't really say if this result is considered really good.

graph Dec 15.jpg
 

Travis Ballstadt

Administrator
Staff member
Joined
Jul 26, 2017
Messages
1,080
Location
Seattle, WA
More  
Preamp, Processor or Receiver
Anthem AVM60
Main Amp
Emotiva BasX 5
Additional Amp
Emotiva UPA-500
Universal / Blu-ray / CD Player
Sony UBP-X800
Front Speakers
NextLevel Acoustics Reference Cinema
Center Channel Speaker
NextLevel Acoustics Reference Cinema
Surround Speakers
NextLevel Acoustics Reference Cinema
Front Height Speakers
NextLevel Acoustics Angled Satellite
Rear Height Speakers
NextLevel Acoustics Angled Satellite
Subwoofers
SVS PB2000
Video Display Device
JVC DLA X790R, Lumagen Radiance Pro 4240
Screen
SeymourAV Proscenium 124” diagonal 2.40:1
Remote Control
Harmony Elite - Moving to Unfolded Circle Remote 2
Streaming Equipment
Kaleidescape Strato C/Terra 48TB/Compact Terra 6TB, PLEX Server, AppleTV4K, Bluesound Node2i
Streaming Subscriptions
AppleTV+, Amazon Prime, HBO Max
Satellite System
They still have those?
Other Equipment
Rega Planar 6, Rega Exact2 cart, Rega Aria Mk3 Phono Stage, Jolida JD202BRC, Rega RS-5 Speakers (2-channel system)
Another idea to toss around, what are your LCR speakers? You could always try tying the subs into your LR channels, and instead of trying to use them to maximize LFE, you could try using them to extend the low end of your LR channels. Just a thought to play with. I’m using an old sub to extend my center right now, and it’s working well enough that I may try to locate two more identical subs to extend my entries front soundstage.
 

ciotime

New Member
Thread Starter
Joined
Nov 25, 2020
Messages
23
More  
Preamp, Processor or Receiver
Denon X3700H
Main Amp
Denon X3700H
Additional Amp
Denon AVR 3313
Universal / Blu-ray / CD Player
Sony
Front Speakers
B&W 602 S3
Surround Back Speakers
B&W 303
Subwoofers
Paradigm PDR12 and PDR10
Video Display Device
BenQ HT3550
Screen
Grandview Tab Tension
Fronts are B&W DM 602 S3 and LCR 60 S3.
 
Top Bottom