Thread Starter
- Joined
- Jan 31, 2020
- Messages
- 54
More
- Preamp, Processor or Receiver
- outlaw audio 976 7.2 balanced receviver
- Main Amp
- Crown xli 800 xls 1502
- Additional Amp
- Crown xli 800 , Crown xli 800
- Other Amp
- crown xls 1502
- Universal / Blu-ray / CD Player
- nvidia shield (2017 model)
- Front Speakers
- PL-89
- Center Channel Speaker
- PL-28II (for sale)
- Surround Speakers
- Klipsch RB-81 (sold)
- Surround Back Speakers
- Klipsch RB-81
- Front Height Speakers
- none
- Rear Height Speakers
- none
- Subwoofers
- none at the moment
- Other Speakers or Equipment
- none
- Video Display Device
- none
- Screen
- Vizio M55-E0 (2017 model) upgrading to tcl 55in
- Remote Control
- none
- Streaming Equipment
- none
- Streaming Subscriptions
- none
- Satellite System
- none
- Other Equipment
- none
what the best fabric option to use for diy acoustic panels an basstraps with images from
Design Fabric Printing
for my diy acoustic panels an basstraps
or from Contrado: Buy or Sell Artist Designs | Print on Demand
https://www.contrado.com/printing-on-florence-net-fabric
or the default
www.contrado.com
would either from this site work
my new acoustic tiles an traps are to be four custom 6in by 36in by 6ft frame-less traps two parallel to either side of the ht room
the plan is to get four six packs of roxul 80 an stack in a row of three deep by three tall after trimming them down to 2ft by 3ft an wrap the 6in thick perimeter in burlap an use duct butter on the burlap an roxul i think that will make it sturdy an rigid then wrap the whole with acoustic fabric
i also plan to some 60 x 10 x 3 mm Neodymium Bar Magnets stitched into the burlap in the back of the acoustic panels so as to adhere the panels to some painted metal strips on the wall which hopeful will allow for ease of placement an remove
would anchoring to just sheet rock with expander screws the total weight would be about 57 pounds
using 6 Neodymium Bar Magnets per tiles should give 72 pounds of pull does anyopne think this will work
or is this a crap shoot
Design Fabric Printing
for my diy acoustic panels an basstraps
or from Contrado: Buy or Sell Artist Designs | Print on Demand
https://www.contrado.com/printing-on-florence-net-fabric
or the default
Custom Speaker Fabric Printing. Custom Speaker Grill Cloth
Custom Speaker fabric designed by you. Order your patterns as test prints or get a swatch pack with all our printed samples. Express delivery.
www.contrado.com
would either from this site work
my new acoustic tiles an traps are to be four custom 6in by 36in by 6ft frame-less traps two parallel to either side of the ht room
the plan is to get four six packs of roxul 80 an stack in a row of three deep by three tall after trimming them down to 2ft by 3ft an wrap the 6in thick perimeter in burlap an use duct butter on the burlap an roxul i think that will make it sturdy an rigid then wrap the whole with acoustic fabric
i also plan to some 60 x 10 x 3 mm Neodymium Bar Magnets stitched into the burlap in the back of the acoustic panels so as to adhere the panels to some painted metal strips on the wall which hopeful will allow for ease of placement an remove
would anchoring to just sheet rock with expander screws the total weight would be about 57 pounds
using 6 Neodymium Bar Magnets per tiles should give 72 pounds of pull does anyopne think this will work
or is this a crap shoot
Last edited:
