Recent content by dan711

Thanks John. Had to take a long break; stressed out. I ended up uninstalling all and going through the setup guide, basically starting over. Think it was ultimately an issue with ASIO and I think the mic cal file was an issue as well. It was just strange that everything worked fine one day...

Everything worked fine yesterday and now I get "output-not connected" "asio has been reset". How and what should I attempt to do?

It definitely sounds better than any other time recently. Mid-bass is back with authority. The anemic sound when watching tv programs has been replaced with a fuller sound for sure. I still want to work on cleaning up that peak @ 55 hz and on up through 120 hz. I want that mid-bass kick but...

Todd or anyone that may care. Took some measurements today after making sure ASIO control and mic inputs were corrected. First set of measurements are center, left, right and l & r combo. I took apart my DIYSG Fusion 8 center and made some adjustments to the enclosure as well as re-wiring. It...

It appears that is correct. When umm-6 is highlighted under device list; micin 1 & 2 appear under input. If I remove umm-6 from device list then micin 1 & 2 disappear. Now, thanks for the help I received here, I think I can properly measure. I'll get some measuring done this weekend and report...

@John Mulcahy No eq applied so not sure whats happening at 7.5 khz. There was no external noise during my last measuring session. House/room was dead quiet. @jtalden ASIO control panel ( umm-6 was not highlighted anymore ), Todd was right in assuming it defaulted back to internal mic. HD...

John, I've attached the file with the center isolated. I'll do more searching later today in order to dig up the mains. Not sure what is causing the craziness @ 90 hz. I've tried both center channels I have and they have had similar results. I'm crossing over at 90 hz but, have tried 80 and 100...

Thanks Todd and Sonnie. This is my first venture with Yamaha and YPAO however, not my first go-round with room correction i.e. Audyssey and MCACC. I know of the issue with most room correction software attempting to label speakers as large. Unfortunately, it's REW measuring that is frustrating...

sorry, was thinking about the routine on other sites.

I've been recently posting over @ AVS so I thought I would bug folks on this forum. I realize that many post on both forums. i.e. AustinJerry, who has given me sound advice. I've been having issues with my sound. It just doesn't seem right. I make adjustments and I get thundering low bass but...

Thanks, Sonnie. I'll try some phase adjustments. Not sure it matters but the graph of the center is without smoothing. Don't yet know enough about REW to know exactly what does or does not matter as much. I adjusted distance (give or take a foot or so) as well as a slight elevation and could...

Countless moves of furniture, speakers and subs. This is the best measurement so far. We use the room primarily for movies and tv so center channel and sub alignment is critical. Blue is un-smoothed center only. Red is subs (3)+ center w/Audyssey engaged. No matter what i did; the peak @ 55 and...

Set up as 7.1. Not sure what happened. I ended up exiting REW and restarting. I finally was able to get subs + center to measure. My windows 10 laptop only produced outputs labeled in REW as Audio 1 thru 8. Audio 1=Left, audio 2=right, audio 3=center, etc. red is no Audyssey green is Audyssey...

Can't seem to figure out how to measure center channel and/or L/R channel along with subs. Measuring subs only-I connected subs to left input on receiver. When I connect subs back to sub input on receiver I get zero sound when using REW. Side note: I see people referencing don't use hdmi 4 for...

Thanks Sonnie for your feedback. I must have moved my subs 15+ locations today. Everything from swapping front to back, side to side, moving one sub then moving two, etc....etc.I witnessed some horrific looking measurements while doing so. The ones posted were some of the better ones. I will...