Finally got it working - input gain in alsa is distinct from mute - and if it gets muted in alsa, I don't see how to unmute at the pulseaudio level. I was looking for this, but missed it somehow.
I'm actually looking for Xmax generated distortion, not Xlim - so I think harmonic content is going to be a more reliable indicator, but I'll give that a try (once I get my inputs working again).
I have a commercial box which is disappointing me, farting out even with a sub handling < 100 Hz...
I was looking for a way to detect excursion limits - maybe generate a signal and look for distortion products? Seems this is something that might not be too difficult in REW.
Ok, after a daylong rabbit trail I have remapped the inputs/outputs:
# Remap Behringer inputs separately
load-module module-remap-source source_name=umc1820-xlr-1 source_properties=device.description=UMC1820-XLR-Input-1 master=alsa_input.usb-BEHRINGER_UMC1820_958E0CDF-00.multichannel-input...
With pulseaudio allowed to utilize the card and PCM: Pulse selected:
Assertion 'uchunk->index % bq->base == 0' failed at pulsecore/memblockq.c:289, function pa_memblockq_push(). Aborting.
Aborted (core dumped)
Only I have ulimit set to unlimited and can't seem to find the core dump.
About four is actually good. Mic 1/2 cannot be removed from monitoring on outputs 1/2 - you can of course change the monitor mix knob. But for Ardour, et al, I run computer generated outs on 3/4, and use 1/2 so that I can route my front panel mics to a wedge speaker. I was using the PC...
Removing the card from pulseaudio seems to prevent the app crash. I still get output but not input if I use UMC1820. Default, PCM: default, or Default device all generate no audio but show output/input/ref levels of -12, -13.93 dbu,-13.93dbu.
Starting it up using roomeqwizard (instead of the...
It runs absolutely fine with Alsa, Jack, or any non-java-sound system in Linux - I use it daily with Ardour, Musescore and SonicVisualiser. I didn't say the computer crashed, I said REW crashed.
"pcm-default just crashes the program"
"If I allow it in pulseaudio mixer, using either pcm...
Yes, pcm: pulse and pcm: default. I normally don't allow pulse audio to play with the multitrack interface because pulseaudio is kinda brain dead. That interface is normally reserved for ALSA. If I allow it in pulseaudio mixer, using either pcm interface in REW causing it to crash with no output
5.20.10_AMD64 shows UMC1820 [plughw[1,0] for both input and output - it plays audio on outputs 1+2, but no visible input on Input1 even though alsamixer shows the gain is up to 0db, and the level is set a few db below clipping.
I'm running into issues again with this card in REWS. To get it to work the first time I had to remove all other sound cards from ALSA and set the mic level in alsa mixer.
When I bring up preferences, for output devices I see: "Default audio device, Pulseaudio Mixer, and UMC1820 [plughw1,0]...
Hi - new to REW. I've done it for my FBQ2496, but I have a much more limited EQ I'd like to use with this cabinet - and it has 4 bands, two of which are shelving. I figured out how to do shelving filters, but the thing is - Match response to target always overrides my filter choices. I set the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.